Daha önce arduino shield (modül) leri hakkında yazı dizimize başlamıştık:

Arduino Shield (modül) Listesi 1

Arduino Shield (modül) Listesi 2

Bugün konumuza kaldığımız yerden devam edeceğiz. Elimizden geldiğince arduino modülüyle ilgili açıklamalar yapmaya çalışıyoruz. Zaten üreticiyi de paylaştığımızdan ilgilendiğiniz arduino modülüyle ilgili daha ayrıntılı bilgiye kolaylıkla ulaşabilirsiniz.

Chesters Garage Power LED Shield

Chesters Garage Power LED Shield
Chesters Garage Power LED Shield
Chesters Garage Power LED Shield2
Chesters Garage Power LED Shield2

Bu modül ile power ledleri sürebilirsiniz. (Ledler 1W ve üstü olabilir.) PWM ile parlaklık kontrol, her kanalın ayrı ayrı akımlarının ayarlanabilmesi gibi özelliklere sahip.

  • 4 individually addressable channels.
  • Each channel adjustable ~50mA to 1000 mA.
  • 1 to 6 LEDs per channel (more if you run strings in parallel)
  • Any combination of LED colors.
  • Full opto-isolation to protect the Arduino.
  • 5V regulator to power the Arduino from the shield.
  • Drives 85 Watts of LEDs from one shield (6 LEDs x 3.6V x 1000 mA x 4 channels)
  • Stackable (estimated up to 8 shields can be stacked)
  • Minimum input voltage: 6 VDC.
  • Maximum input voltage: 32 VDC.

Chips To Bits Storage Shield

Storage Shield ile depolama yapabilirsiniz. FAT formatında SD kart içinde depolama yapabilirsiniz. Bunun anlamı PC ile kart okuyucu ile depoladığınız veriyi görebilirsiniz demek.

Features:

  • Low memory overhead on the Arduino board.
  • Support for FAT12, FAT16, and FAT32.
  • Support for 8.3 format (LFN is not supported)
  • Direct disk access (Not fully implemented)
  • Embedded real time clock using a DS1307 real time clock.
  • Provides accurate timestamps on files.

3.2″ Touchscreen Shield

3.2

Tags:lcd, touch, sd, flash, storage, rtc
Maker:  Circuit Ideas Design
Display time logger application shield.

    • TFT LCD 3.2″ touch screen.

 

  • SD card slot.

 

 

  • RTC I2C DS1307.

 

 

 

USB Host Shield

 

USB Host Shield

Shield URL:USB Host Shield

Tags:

Maker:Circuits At Home

This shield adds USB Host capabilities to the Arduino. Comes in four different configurations. Software support for new devices is constantly added; at the moment, code for USB keyboard and PS3 controller are ready with Bluetooth and digital cameras in the works.

DTMF Shield

DTMF Shield
DTMF Shield

Ses girişinden alınan DTMF tonlarını çözmek için kullanılıyor. Radyo üzerinden arduino ile cihazları kontrol etmek için kullanılabilir.

Shield URL:DTMF Shield

Tags:dtmf, audio, input

Maker:Collin Schulz

DOGS102 LCD Shield

DOGS102 LCD Shield
DOGS102 LCD Shield

Shield URL:DOGS102 LCD Shield

Tags:lcd, display, output

Maker:Control Connection

LCD shield based on DOGS102W display from Electronic Assembly:

  • 102×64 monocrome resolution with Amber backlight.
  • 3.3V SPI interface with CD4050 buffer.
  • SMD componens mounted on the back.
  • Optional 5V to 3.3V regulator and PWM backlight control.
  • 4 buttons for easy menu navigation.

Accelerometer Shield

Accelerometer Shield
Accelerometer Shield

Shield URL:Accelerometer Shield

Tags:

Maker:Critical Velocity

Integrates an Analog Devices ADXL335 3-axis accelerometer into an Arduino compatible shield. 3 analog outputs for the X,Y and Z axes. +/3 g range per axis.

  • 3 Axis Acceleration, +/- 3g sensing range per channel.
  • 6 PWM Servo output headers.
  • Prototyping space.
  • 8 and 6 pin shield extender headers and regular headers included.
  • Reset button included.

IMU Shield, 6 DOF Accel/Gyro

IMU Shield, 6 DOF Accel/Gyro
IMU Shield, 6 DOF Accel/Gyro

Shield URL:IMU Shield, 6 DOF Accel/Gyro

Tags:

Maker:Critical Velocity

The Critical Velocity IMU (Inertial Measurement Unit) Shield provides 6 degrees of freedom – X, Y, Z acceleration, and angular yaw, pitch and roll rate sensing.

Full scale accelerometer range is +/- 3 g, and the gyroscope has a selectable range of +/- 300 deg/sec or +/ 1200 deg/sec.

  • 6 Degrees of Freedom – 3 Axis Acceleration and 3 Axis Gyro.
  • Digitally selectable gyroscope sensitivity – 300 or 1200 deg/sec.
  • Digitally selectable gyroscope reference voltage measurement.
  • Shield stacking headers and regular headers included.
  • Uses Analog Devices ADXL335 3-axis accelerometer.
  • Uses ST Microelectronics LY530AL and LPR530AL Gyroscopes.

32 Channel Analog Multiplexer Shield

32 Channel Analog Multiplexer Shield
32 Channel Analog Multiplexer Shield

Shield URL:MonsterMux 32 Channel Analog Multiplexer Shield

Tags:analog, input

Maker:Critical Velocity

The MonsterMux32 Arduino-Compatible Shield Kit allows you to connect up to 32 analog channels into a single analog input pin on the Arduino board. 6 digital pins control which input is connected to the Arduino.

  • 32 Analog channels.
  • 36 rising-clamp terminal block pins.

Terminal Block Shield

Terminal Block Shield
Terminal Block Shield

Shield URL:Terminal Block Shield

Tags:breakout

Maker:Critical Velocity

Breaks out each pin into its own high quality rising-clamp terminal block connector for easy hookup to external devices. 30 terminal connections in total.

FM Radio Shield

FM Radio Shield
FM Radio Shield

Shield URL:FM Radio Shield

Tags:fm, radio, receiver

Maker:Curious Inventor

FM receiver that allows you to control the station digitally, read signal strength, and obtain RDS info including artist, song, and station call-sign.

  • Ultra clear audio due to onboard DSP signal conditioning.
  • RDS station info.
  • Measure the signal strength to find strongest or weakest stations. Good for finding an empty band for your FM transmitter, or auto-programming your radio in a new location.
  • Includes amplifier for headphones.
  • Antenna connection point available, uses headphone wire for antenna by default.
  • Change Volume / Station with buttons or Serial USB commands.

Li-Ion Battery Shield

Li-Ion Battery Shield
Li-Ion Battery Shield

Shield URL:Li-Ion Battery Shield

Tags:battery, charge, power

Maker:CuteDigi

This shield is used to provide a rechargable battery pack for the Arduino.

The mini-USB port is used to charge a Li-Ion or Lo-Ion poly battery. There are LEDs showing the charge status.

6 big mounting holes can help you easily fix the battery pack.

For a 600mAH battery, it takes about half hour to charge.

Quad-band GPRS/GSM Shield

Shield URL:Quad-band GPRS/GSM Shield

Tags:gprs, gsm, communication

Maker:CuteDigi

This is an Arduino Shield for SM5100 quad-band GSM/GPRS module. The module is included.

RS232 Shield

Shield URL:RS232 Shield

Tags:serial, communications

Maker:CuteDigi

Adds an RS232 serial port to your Arduino.

Not: Arduino modülleri yazı dizimiz devam edecek. Yazımızdan faydalandıysanız bir teşekkürü çok görmeyiniz lütfen.

  • Levent

    Güzel liste. Teşekkür ederiz.

  • Pingback: Levent()

  • Tuzlalı

    Arduino kullanmaya mı başlasak acaba? İnsanın canı çekiyor.

  • mücahi

    merhabalar. size teşekkür ederim bu yazdığınız değerli bilgiler için.
    mekatronik 1.sınıf ögrencisiyim son 1 haftadır hergün bir yeni bilgi öğrenmek icin bu siteye giriş yapıyorum ve buradan çıkmak benim için baya zor oluyor harika şeyler öğrendim.

  • Değerli yorumlarınız için teşekkürler arkadaşlar.